M4. Amplitude and Lift Angle
What It Is
The amplitude is how far the balance turns from rest to the end of its swing, in degrees.
The lift angle is the arc of the balance’s swing during which the impulse pin is in the fork: from the unlock to the drop. It is set by the movement’s design. The calibre table gives it where it is known.
How It Is Worked Out
The balance swings like a pendulum: its angle follows a sine wave of
amplitude A and period T, one full oscillation, two beats. Near the
middle of its swing it passes through the lift angle L, centred on the
rest point. The time t it takes is short when the swing is wide, since
the balance is moving fastest there.
Solving for A gives the formula Witschi’s timegraphers and the open
tg program use:
A = L ÷ (2 × sin(π × t ÷ T))
An example. At 28,800 bph, T is 250 ms. With a lift angle of 52°
and an unlock-to-drop time of 8.0 ms:
A = 52 ÷ (2 × sin(π × 8.0 ÷ 250)) = 52 ÷ (2 × 0.1004) ≈ 259°
Timing the unlock and the drop:
- Beats are grouped into 2 s windows. In each, the Ticks’ sounds are averaged into one shape, and the Tocks’ into another. Each side needs 3 good beats. The average keeps the middle half of the beats at each moment, which ignores stray clicks.
- On each shape, both edges are timed where a sound crosses half its
own height:
- The drop is where the rise into the drop’s peak crosses half the drop’s height. It is found by walking back from the peak, at most 2 ms, so an earlier sound near that height isn’t taken for it.
- The unlock: the first sound is found as the first steady rise above the background by 2% of the drop’s height (or 4 times the background’s noise, if that is more). It is timed where it crosses half its own height.
- Each window gives a Tick and a Tock amplitude. The window’s amplitude is their mean. A window with one side missing is left out of the reading, and kept in that side’s own figure.
- The reading is the median of its windows’ amplitudes.
Why This Way
- Half-height crossings on rising edges, not peaks: an edge’s time is sharper and steadier than a peak’s, which moves with the sound’s shape. Taking each sound at half its own height keeps a quiet unlock from being timed by the drop’s loudness.
- Averaged beats: a single beat’s unlock is too faint to place. Averaging a few seconds of beats brings it out of the noise, while still following an amplitude that changes.
- The median of windows: an edge marked on the wrong sound moves one window, not the reading.
When You’d Use It
- After service, to compare amplitude before and after, in the same position and state of wind.
- Across positions, to compare the swing lying flat and standing (chapter 20).
- Over the power reserve, to see the swing fall as the mainspring runs down (chapter 21).
- Against the rate, to see whether the rate follows the amplitude (isochronism, chapter 19).
What It Helps Find
The amplitude shows how much energy reaches the balance. A low or falling amplitude can come from the mainspring, the train, the escapement’s lubrication or wear, or the balance’s pivots. The amplitude alone doesn’t say which.
What It Can’t Tell You
- Without the right lift angle, the true amplitude. Every amplitude is in proportion to the lift angle: 52° used for a 55° movement reads every amplitude about 5% low. With no calibre set, the app uses 52°, and Lift’s hover on the Calibre card says it is the default.
- Through a poor unlock. The amplitude rests on timing a quiet sound. A 1 ms error in the unlock-to-drop time moves it a lot: at 28,800 bph and 52°, 8.0 ms reads 259°, and 7.0 ms reads 296°. A muffled holder, clipping or automatic gain moves the unlock, and with it the amplitude.
- The swing’s two halves exactly. The Tick and Tock amplitudes in the hover can differ because the two sides sound different, not because the balance swings further one way.
Previous: M3. The Sound Card’s Clock · Next: M5. Beat Error
This page comes from the app's user guide at v1.0.1. See it on GitHub.